Line Vty 0 Password |
||||||
| ||||||
|
line vty 0 4. password enter-here. login. The password is the same for all five virtual terminals. ... line vty 0. cisco-2501(config-line)# password number1 ... www.groupstudy.com For security reasons, you must define a vty line password. ... Ciscozine(config)#line vty 0 4. Define your vty lines password ... www.ciscozine.com Example 4-5 Line Configuration Mode for vty 0 Through 4 ... line con 0 login line 1 16 line aux 0 line vty 0 4 exec-timeout 15 0 password 7 ... www.ciscopress.com To enable telnet logins with the password PaSsWoRd: conf t. line vty 0 4. login. password PaSsWoRd ... made it available through line aux 0 instead of vty 0 4. ... www.tech-recipes.com no service password-encryption. hostname A-cisco. username B-cisco password 0 Jonn ... line aux 0. line vty 0 4. no login. end. Current configuration: version 12.0 ... www.computerfreetips.com router>enable Enter password: router#conf t router(config)#line vty 0 4 router ... Finally, the new password was added to the vty line. ... www.verio.com ... login line aux 0 transport input all line vty 0 4 password passwordhere login ! ... line vty 0 4 (config-line)#login (config-line)#password <password_here> ... www.pantz.org router(config)#line vty 0 4. router(config-line)#password sanjose. router ... line vty 0 4. password 7 001712080E541803 << newly configured password encrypted ... www.sunsetlearning.com line vty 0 4. privilege level 15. password baseball. login ... username ed privilege 15 password 0 mcdaniel. line vty 0 4. login local ... www.articlealley.com Example 4-5 Line Configuration Mode for vty 0 Through 4 ... line con 0 login line 1 16 line aux 0 line vty 0 4 exec-timeout 15 0 password 7 ... www.informit.com Managing vty Lines You can open additional lines using the line vty command. Before users can access the lines, you must configure a password, disable login using the no login command, or configure AAA authentication on the lines. Use the show line vty command to monitor vty lines. www.juniper.net/techpubs/software/e...Vty Line Authentication and Authorization NOTE: To use an encrypted password or a secret, you must follow the procedure in Setting Basic Password Parameters to obtain the encrypted password or secret. You cannot create your own encrypted password or secret; you must use a system-generated password or secret. www.juniper.net/techpubs/software/e...Multilink PPP on Back-to-Back Routers with Multiple Serial... ! line con 0 line aux 0 transport input all line vty 0 4 login ! end. Current configuration: version 12.2 hostname Router2 ! ! username Router1 password 0 abc ip subnet-zero no ip domain-lookup ! ! interface Loopback0 ip address 192.168.20.1 255.255.255. ! dialer-list 1 protocol ip permit ! line con 0 line aux 0 line vty 0 supportwiki.cisco.com/ViewWiki/inde...Cisco - Catalyst 4908G-L3 VLAN Routing and Bridging Example... The line vty 0 4 command enters into line configuration mode, so we can define a password for inbound Telnet sessions on the virtual terminal (vty) lines. The password command defines a password to enter normal mode on the switch through a Telnet session on the vty lines. 2 throughput 0 link delay 0 received 0 www.cisco.com/warp/public/473/40.ht...Howto presenting HSRP Protocol classless no ip http server no ip http secure-server control-plane www.szukalak.ovh.org/Cisco - Cable Voice Adapter 120 Basic Installation and... hostname CVA ! enable secret < password > [Choose a strong password with at least one capital letter, one number, and one special character.] no ip domain-lookup ! line vty 0 4 password cisco end. Current configuration : 1099 bytes ! version 12. www.cisco.com/warp/public/109/cva.s...Reverse telnet Wikipedia: A typical server configuration on a Cisco router would look like this: version 12.3 service timestamps debug uptim service timestamps log uptime no service password-encryption ! hostname Terminal_Server ! ip host Router1 2101 8.8.8.8 ip host Router2 2102 8.8.8.8 ip host Router3 2113 8.8.8. en.wikipedia.org/wiki/Reverse_telne...Vty Line Authentication Note: To use an encrypted password or a secret, you must follow the procedure in Setting Basic Password Parameters earlier in this chapter to obtain the encrypted password or secret. You cannot create your own encrypted password or secret; you must use a system-generated password or secret. www2.juniper.net/techpubs/software/...Cisco - Advanced Queuing Techniques in the Cisco IOS version 10.0 ! hostname router1 ! enable password cisco ! ! interface Ethernet0 ip address 144.254.1.1 255.255.255.0 no mop enabled ! interface Serial0 ip address 144.254.2.1 255.255.255.0 custom-queue-list 1 ! interface Serial1 shutdown ! router igrp 109 network 144.254.0. version 10.0 ! hostname router2 ! enable password www.cisco.com/warp/public/614/15.ht...Layer 2 Tunneling Protocol (Version 3) Static Method and... version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname R4 ! ! ip subnet-zero ! interface Ethernet0 /0 ip address 30.30.30.4 255.255.255.0 no ip directed-broadcast ! router ospf 1 log-adjacency-changes network 30.30.30.0 0.0.0.255 area 0 ! ip classless ! line con 0 supportwiki.cisco.com/ViewWiki/inde...Catalyst 4507R and VRF-Lite -- http://dcp.dcptech.com > -----Original Message----- > From: cisco-nsp-bounces (at) puck.nether.net > [mailto:cisco-nsp-bounces (at) puck.nether.net] On Behalf Of > Francisco Rivas > Sent: Tuesday, February 06, 2007 9:29 AM > To: cisco-nsp (at) puck.nether. www.threebit.net/mail-archive/cisco... | ||||||
| Last Updated ( Tuesday, 17 March 2009 ) | ||||||
Main Menu
Current ArticlesLogin FormSyndicate
|
Home
 More CCNP Study Sites |
Design by RocketTheme © 2005 - 2006 All Rights Reserved