Home arrow More CCNP Study Sitesarrow Enable Erase Startup Config Reload Cisco

Enable Erase Startup Config Reload Cisco
E-mail
Written by Wendell E. Jaynes   
Saturday, 28 March 2009
 

www.usfca.edu/~villegas/ccna/2/ch6/lab2/index.html
You can download the Cisco TFTP server at no cost from the web site listed below. ... copy running-config. erase startup-config. reload. Resources Required: ...
http://www.usfca.edu/~villegas/ccna/2/ch6/lab2/index.html

Router Interface Summary  [Adobe PDF]
Startup config file not load when we reloaded the router? ... At the privileged EXEC mode, enter the command erase startup-config. Router#erase startup-config ...
http://www.cod.edu/people/faculty/wagnerjo/labs/CCNA2_lab_5_1_5_en.pdf

Devices
Cisco IOS Supported Commands: Routers ... enable. erase startup-config. exit. logout. ping WORD. reload. show. access-lists { <1-999> | WORD } ...
http://www.it.uniovi.es/docencia/GestionGijon/redes/Comandos-IOS-Routers.htm

Cisco Routers - HiSeasNet Operations - HiSeasNet Wiki
... using the Cisco copy command to the startup-config file (or startup-confg in ... Reload the server with a reset command. Enable yourself with an enable. ...
http://hiseasnet.ucsd.edu:16080/wiki/display/hsnops/Cisco+Routers

CCNA 2: Routers and Routing Basics v3.1.1 Student Lab Manual
lab manuals in cisco ccna 2. what does router(config-router) mean? ... Router>enable At the privileged EXEC mode, enter the command erase startup-config. ...
http://www.scribd.com/doc/6564522/CCNA-2-Routers-and-Routi...-v311-Student-Lab-Manual-

Cisco Commands
copy running-config startup-config. erase startup-config. write. clock set. clear. reload ... enable secret. ip domain-name. ip host. ip http server. ip name ...
http://www.howtonetwork.net/public/department98.cfm

Cisco CCNA Network Simulator: Supported CCNA router commands
enable secret <password> 23. erase startup-config. 24. encapsulation <encapsulation-type> ... reload. 31. show interfaces. 32. show history. 33. show version ...
http://routersimulator.certexams.com/commands.html

CiscoKits.com - CCNA CCNP and CCIE Certification Training Kits ...
... erase the saved configuration and reload the box. 2950sw1# erase startup-config ... 2950sw1(config)# enable password cisco. 2950sw1(config)# interface vlan1 ...
http://www.ciscokits.com/to-be-done-new/LAB_16_CATALYST_2950_SWITCH_CONFIGURATION.php

Recover lost passwords using Cisco configuration registers
enable secret 5 $1$Tde5$qCheBIgD/VoIaWm.YOtCE ... Instead, I could either erase the startup-config, or I could load it into the ...
http://articles.techrepublic.com.com/5100-10878_11-6105879.html

Cisco Systems: PIX Firewall - How to erase startup config
reload Halt and reload system. restart Restart a machine. who Show active ... enable password 000000000000000000000000000000 encrypted. hostname localdirector ...
http://www.tek-tips.com/viewthread.cfm?qid=1486188&page=1

 


Cisco - Resetting Catalyst Switches to Factory Defaults

Switches running Cisco IOS Software have a running configuration file and a startup configuration file. The RAM stores the running configuration, and the NVRAM stores the startup configuration. When you make a configuration change to a switch running Cisco IOS Software, the change becomes part of the running configuration.

www.cisco.com/warp/public/473/156.h...
How to reset a Cisco router to factory default (removing the...

To change the configure register to recognize the startup configuration, issue the config-register command, as shown in this example: Router (config)# config-register 0x2102. To save the blank configuration, issue the copy-running config-startup config command.

napps.networkworld.com/community/no...
First-Time Startup and Basic Configuration

This chapter describes basic system startup and use. Information in this chapter will help you with these tasks: First-time startup and basic configuration of the Cisco router/bridge using the setup command facility.

www.cisco.com/univercd/cc/td/doc/pr...
Cisco - Password Recovery Procedure for the Cisco 1600 Series...

Type configure memory or copy startup-config running-config in order to copy the nonvolatile RAM (NVRAM) into memory.

Important: Do not type copy running-config startup-config or write. These commands erase your startup configuration.

hostname (config) #enable secret cisco.

End with CNTL/Z. Router (config

www.cisco.com/warp/public/474/pswdr...
Cisco CCNA Certification Knowledge to Pass the Exam

There are two basic configuration files for each router: startup and running. Startup configuration is held in NVRAM and is accessed when router is started. The startup configuration is placed in RAM for the router to run. Following command will display the startup configuration.

www.ciscokits.com/cisco-ccna-exam/
Tomato (firmware) - Wikibooks, collection of open-content textbooks

New model line, released after the version 5 WRT54G, which returns to a Linux-based OS as opposed to the VxWorks firmware. SpeedBooster is not enabled in stock firmware, however third-party firmware will enable the feature. The hardware is essentially the same as the WRT54G version 4.0.

en.wikibooks.org/wiki/Tomato_Firmwa...
Cisco ASA 5580 Adaptive Security Appliance Command Line...

To enable the ICMP inspection engine and ensure that ICMP responses may return to the source host, enter the following commands:

hostname (config)# class-map ICMP-CLASS.

hostname(config-cmap)# match access-list ICMPACL.

scc.cisco.com/en/US/docs/security/a...
Crynwr Software

Crynwr Software.

www.crynwr.com/
Diary Harry Chan Putra » 2007 » March

After successfully copying the Cisco IOS image to the router, make.

sure that you change the configuration register back to 0×2102 and reload the.

router to boot from the Cisco IOS image.

harrychanputra.blog.friendster.com/...
Re: to give free ccna questions and answers -- Practice Tests for...

erase running-config and then reload

erase running-config

no running-config and then reload

voy.com/182650/17.html
The Security Tutorial Zone: cisco pix, wep cracking, backtrack,...

Finally if we want to clear everything and start from afresh we can use the command ‘write erase’.

Firewall#write erase (or wr er for short)

You will be prompted to confirm that you do want to erase the start-up configuration, hitting Enter or typing Yes will clear the configuration.

www.securitytutorials2.thetazzone.c...


Last Updated ( Saturday, 28 March 2009 )
Design by RocketTheme © 2005 - 2006 All Rights Reserved